Showing posts with label on. Show all posts
Showing posts with label on. Show all posts
Friday, November 14, 2014
Nokia 6233 Camera Not Working
Nokia 6233 Camera Problem Camera Operation Failed Camera On Standby Camera Not Working
Sunday, November 2, 2014
samsung e250 hang on start up logo
Thiss hardware problem just reball the main Ic,
Power Ic & charger,tested by me 100times,
Sunday, October 26, 2014
Nokia E73 Power ON OFF Switch Solution
Heres the solution for Nokia E73 Power ON and OFF Switch when damaged. This solution shows the connection line paths of Nokia E73 power switch and can be used where to apply or mend a jumper wire when the power switch terminal solder pads is already lifted or damaged.
Just refer to the solution below and trace the power ON OFF switch tracks.
The Nokia E733 power ON-OFF switch is connected to a 10K resistor this goes through to the power IC (GAZOO). The other terminal side of the 10K resistor is connected directly to the battery supply voltage which is 3.7 volts.
Just refer to the solution below and trace the power ON OFF switch tracks.
Nokia E73 Power ON OFF switch Jumper Ways
The Nokia E733 power ON-OFF switch is connected to a 10K resistor this goes through to the power IC (GAZOO). The other terminal side of the 10K resistor is connected directly to the battery supply voltage which is 3.7 volts.
Friday, October 17, 2014
Nokia X2 05 On Off Power Button Jumper Ways Problem Solution
Nokia X2-05 is not getting power On and it can make charging. It is 100% fault of on off button in it.because On Off button on keypad is not working so that it will not be able to power On.
After disassambly of Nokia X2-05 look at the motherboard for rust carbon or burren parts. If you found some rust or carbon apply electronics cleaner on the mother board and apply hot air to make it dry proper.
Applying too much heat can damage the mother board and parts.It also can be harm for your skin.So keep in mind about normal heat flow when making it dry.Nokia X2-05 Mic problem solution jumper ways
Nokia X2-05 power button On Off switch not working ways jumpers.Replace battery and check if mobile can not be switch On dis assemble the phone and check power switch button ways as given in above diagram.If any print out of these is missing apply jumpers to solve On Off Button problem in Nokia X2-05 .
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
After disassambly of Nokia X2-05 look at the motherboard for rust carbon or burren parts. If you found some rust or carbon apply electronics cleaner on the mother board and apply hot air to make it dry proper.
Applying too much heat can damage the mother board and parts.It also can be harm for your skin.So keep in mind about normal heat flow when making it dry.Nokia X2-05 Mic problem solution jumper ways
Nokia X2-05 power button On Off switch not working ways jumpers.Replace battery and check if mobile can not be switch On dis assemble the phone and check power switch button ways as given in above diagram.If any print out of these is missing apply jumpers to solve On Off Button problem in Nokia X2-05 .
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Monday, September 22, 2014
How to Set Up Your Facebook Account on Sony Xperia S
1. On your devices homeLcd tap on
2. Then tap on Settings and go to Accounts & sync.
3. The Active auto-sync checkbox should be marked to make sure that applications can synchronise data automatically.
4. Tap on Add Account and then Facebook.
5. Just follow the registration wizard to create an account or you can sign in if you already have one.
6. Once youre done, select a synchronisation option for your account and tap on Finish.
Your Facebook account is now set up to work on your phone.
Sunday, September 21, 2014
How to Get More Storage on Motorola Moto G
Moto G has an internal storage capacity of 8GB or 16GB, and MicroSD card slot is not available on this device. But you do get 15GB of free storage on Google Drive and in some regions theres also an extra 50GB which is free for two years. You can redeem it within 30 days of activating your Moto G. Check Google Drive app for more information.
Thursday, September 18, 2014
How to Start Conference Calls on Sony Xperia Z
To start a conference call
1. During an ongoing call, tap
2. Dial the number of the second participant and tap Call. After the second participant answers, the first participant is put on hold.
3. Tap
to add the second participant to the conference call.
4. Repeat steps 1 to 3 to add more call participants.
To have a private conversation with a conference call participant
1. During an ongoing conference call, tap {0} participants.
2. Tap the telephone number of the participant with whom you want to talk privately.
3. To end the private conversation and return to the conference call, tap.
To release a participant from a conference call
1. During an ongoing conference call, tap the button showing the number of participants. For example, tap 3 participants if there are three participants.
2. Tap
next to the participant you want to release.
To end a conference call
• During the conference call, tap End conference call.
Read More..
1. During an ongoing call, tap
2. Dial the number of the second participant and tap Call. After the second participant answers, the first participant is put on hold.
3. Tap
to add the second participant to the conference call.4. Repeat steps 1 to 3 to add more call participants.
To have a private conversation with a conference call participant
1. During an ongoing conference call, tap {0} participants.
2. Tap the telephone number of the participant with whom you want to talk privately.
3. To end the private conversation and return to the conference call, tap
.To release a participant from a conference call
1. During an ongoing conference call, tap the button showing the number of participants. For example, tap 3 participants if there are three participants.
2. Tap
next to the participant you want to release.To end a conference call
• During the conference call, tap End conference call.
Saturday, August 30, 2014
How To Install CWM ClockWorkMod Us Recovery on HTC Android Phones
By default, Android powered HTC Smartphones comes with Locked Bootloader and default Recovery firmware which is not so much useful and handy. ClockWorkMod recovery is a very simple and feature rich recovery software which gives many features like Backup and Restore, Mount as USB etc which are mostly not available on stock Firmware or recovery software.
To install CWM Recovery, you first have to Unlock your devices bootlaoder and then Root your phone. After going through these two processes you will be able to install ClockWorkMod recovery on your HTC mobile phone. Although, now doing these two things may seem very difficult, but actually these are very simple to do and at the end youll have a freedom in your device, freedom to do anything or install any custom ROM on your device. Please note that Unlocking botloader and Rooting your phone will void your warranty, so do it at your own risk. Here, i am using HTC Desire C, so the actual process or steps may vary phone to phone.
How to Install ClockWorkMod Recovery on Your HTC Smartphone:
- First of all, as mentioned above you have to unlock the Boot loader of your device. To do this, follow this guide:
How to Unlock Bootloader of HTC Mobile Phone. - Now, next item comes Rooting process. For this, follow this guide:
How to Root Your HTC Android Phone. - Go to this link to download the ClockWorkMod Touch For HTC Desire C:
http://forum.xda-developers.com/attachment.php?attachmentid=1257426&d=1344803585
For other phones search on Google: ClockWorkMod For Your Device Name and download the file given there. - Extract the downloaded archive to C:Android folder.
- Now Boot your phone to bootloader. For this:
Remove the battery.
Put the battery and press Vol Down+ Power button.
Select Fastboot, now it will say USB Fastboot - Open Command prompt by going to start menu and typing cmd.
- In command prompt window, type the following :
cd C:Android - Now type the following and hit Enter:
fastboot flash recovery recovery.img - Thats all. Restart your phone and youve successfully installed CWM Recovery on your HTC Android phone
Friday, August 29, 2014
How To Root Your Galaxy Note 8 0 GT N5110 Android 4 2 2 Firmware Running on Guide
Samsung Galaxy Note 8.0 GT-N5110 (WiFi) recently get updated to the N5110XXCMK1 4.2.2 Jelly Bean Firmware. If you yet to update the firmware, then update the same by following the above link. Hope you updated this latest firmware on your device and now you can root the same using our simple tutorial below. The below guide will help you to root XXCMK1 4.2.2 Jelly Bean Firmware running on Galaxy Note 8.0 GT-N5110. Continue reading the tutorial for complete guide.
After updating official firmware, your device no longer belongs to rooted device. So, after official firmware update, many of us prefer to root our device to enjoy some additional features that unrooted android device doesnt offer. With a rooted android device, you can install apps that ask root permission, flash various custom ROMs, install MODs and tweak various features. Root removes default bloatware apps that free-up lots of memory space and extend the battery life. However, once rooted, manufacturer warranty will be void. But you can regain the warranty by following proper unroot process. To know more about benefits of rooting android device, read- Complete Note on What is Rooting and Benefits of Rooting Android Tablet.
So, want to root Galaxy Note 8.0 GT-N5110 Running N5110XXCMK1 4.2.2 Jelly Bean Firmware? Continue reading this page to get all the necessary steps to successfully root your device. The root file (CF-Auto-Root) we used in this tutorial is safe and have nearly 100% success rate. Well use Odin software to flash the root file.
The tutorial is made with simple step by step guide, so that even an android newbie user can follow and successfully root his/her device. However, in this process you may loss your personal data and settings. So, we recommend you to follow all the backup instructions before proceed to rooting guide.
So, want to root Galaxy Note 8.0 GT-N5110 Running N5110XXCMK1 4.2.2 Jelly Bean Firmware? Continue reading this page to get all the necessary steps to successfully root your device. The root file (CF-Auto-Root) we used in this tutorial is safe and have nearly 100% success rate. Well use Odin software to flash the root file.
The tutorial is made with simple step by step guide, so that even an android newbie user can follow and successfully root his/her device. However, in this process you may loss your personal data and settings. So, we recommend you to follow all the backup instructions before proceed to rooting guide.
All the above pre-requisites are very important and must be followed before proceed to installation guide. Hope you get all the above points and done as mentioned. Now, you are ready to move to the final step of this tutorial where we have arranged a step by step details guide to root Galaxy Note 8.0 GT-N5110 running N5110XXCMK1 4.2.2 Jelly Bean firmware.
Steps to Root Galaxy Note 8.0 GT-N5110 Running N5110XXCMK1 4.2.2 Jelly Bean through Odin:
- Download CF-Auto-Root for Galaxy Note 8.0 N5110 and extract the Zip file: CF-Auto-Root-konawifi-konawifixx-gtn5110.zip
- Download Odin 3.09 and extract the Zip file: Odin3_V3.09.Zip
- Now, Switch off your Tablet and boot Galaxy Note 8.0 N5110 into Download Mode by pressing and holding the Volume Down+Power buttons together (long press until the boot screen appear), now press Volume Up key to proceed to Download Mode.
- Run the Odin3 v3.09.exe file as an administrator (Right click on the .exe file and click on Run as administrator)
- Now connect your Galaxy Note 8.0 N5110 to your computer via USB cable
- In Odin3 screen, you should see a COM Port number like “0:[COM7]” at ID:COM section and “Added!” text at the message box. This means your device has been detected by Odin3.
- Make sure that, only the “Auto Reboot” and “F. Reset Time” options are checked.
- Now, click on the PDA button and select the CF-Auto-Root-konawifi-konawifixx-gtn5110.tar.md5 file.
- Finally, click on the Start button to begin the rooting process, wait few moments.
- Once completed, you would see “PASS!” message in ID:COM port having green background
- Your Tablet should automatically reboot after completion
- You can now disconnect your Tablet from computer
- Finish
Tuesday, August 26, 2014
How to Add a Geotag on a Photo on Sony Xperia Z1
Adding a location to those photos somehow adds relevance and it gives you that flashback of memories when you view those nicely captured moments. Well, this feature is not new any longer since its been there online and you often use them on photo-filtered websites. On your device, you can now add geotags on your photos right on your handset. Heres how you can add geotag on your photos.
1. Open your photo gallery on your device.
2. When youre viewing a photo, just tap the screen and the toolbars will display.
3. Now tap
to open the map screen.
4. Find and tap the desired location to put the map on the photo.
5. To adjust the location of the photo, just tap the location on the map to where you want to move the photo.
6. Tap OK when youre done and to save the geotag. You can then return to the photo viewer screen.
Read More..
1. Open your photo gallery on your device.
2. When youre viewing a photo, just tap the screen and the toolbars will display.
3. Now tap
to open the map screen.4. Find and tap the desired location to put the map on the photo.
5. To adjust the location of the photo, just tap the location on the map to where you want to move the photo.
6. Tap OK when youre done and to save the geotag. You can then return to the photo viewer screen.
Saturday, August 23, 2014
How to Root Samsung Galaxy Note 3 Neo 3G SM N750 on Using Android 4 3 Jelly Bean Firmware
This tutorial uses CF-Auto-Root file released by Senior Recognized XDA-Developers, Chainfire. Head over to the CF-Auto-Root main thread to learn more about the root method.
Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!
Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 3 Neo on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 percent.
5. The CF-Auto-Root file works only on the 3G version of Galaxy Note 3 Neo (SM-N750). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 3 Neo by navigating to Settings >> About Phone.
Files Required
1. CF-Auto-Root (CF-Auto-Root-hl3g-hl3gub-smn750.zip)
2. Odin 3.09
Steps to Root Galaxy Note 3 Neo (3G) SM-N750 Running on Android 4.3 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.09 files using WinRAR/7-Zip/WinZip or any other extracting tool.
Step 2: Switch off the Galaxy Note 3 Neo. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy Note 3 Neo to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the AP button and select the CF-Auto-Root-hl3g-hl3gub-smn750.tar.md5 file.
Step 6: Verify that Auto Reboot and F. Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is NOT selected.
Step 7: Double-check and click Start button in Odin. The installation process will now begin.
Step 8: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.
Samsung Galaxy Note 3 Neo (3G) SM-N750 running on Android 4.3 Jelly Bean is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.
Note: Many Samsung devices store a flash counter that keeps track of how many times you have flashed custom firmwares to your device. Triangle Away can be used to reset the flash counter to zero.
How to Fix "Unfortunately, SuperSU has stopped"?
Step 1: Download and install the latest APK of SuperSU on your device.
Step 2: Open SuperSU app (update the binary if prompted) and allow it to disable KNOX.
Step 3: Reboot your device.
Friday, August 22, 2014
Rooting Galaxy S4 I9500 on Official JB 4 2 2 XXUBMGA OS
Having a rooted handset means that you are an advanced Android user who is always trying to use its smartphone on full power by enjoying all the features, apps and capabilities that are available on the market. So, gaining root access is extremely important especially if you have a high end phone, like the Samsung Galaxy S4 I9500. That’s why by using this tutorial you will be able to learn how easily root the Galaxy S4 that runs on stock / official Android 4.2.2 Jelly Bean XXUBMGA firmware.
This process will be easy to complete as Odin will be used for applying the root package on your SGS4. Actually you will flash a rooted JB 4.2.2 XXUBMGA OS on your device, which means that the operation will be similar with an update one. Do note that the root task in though unofficial, so the warranty of your S4 will get void. Anyway, this is not permanent, meaning that you can anytime choose to revoke the root access for reclaiming and regaining the warranty back. For revoking root access you will have to update your Galaxy S4 I9500 with an official release of the Android system, or you will have to downgrade to stock Jelly Bean 4.2.2 XXUBMGA software.
The advantages of root are numerous, but I do have to mention the following ones: on a rooted system you can access the OS and the internal system of the device for performing different operations such as removing in built programs or customize the performances; also on rooted handsets you can install a custom recovery image which can then be used for flashing custom ROMs and custom kernels; then, of course you will be able to overckock your Android device, or undervolt the same in case you need to upgrade the battery life; finally and as you may know, rooting is the first step to do when trying to speed up and upgrade the battery life of your smartphone / tablet.
Anyhow, before rooting your galaxy S4 just remember that the warranty will get void. So, be careful and try not to mess things up. Read the guidelines from below and everything will be fine.
Backup the text messages, call logs, internet settings, market apps and everything that’s important for you as the Galaxy S4 system might get wiped out or your data might get corrupted while applying the steps from below. If you want to avoid the unpleasant situation in which you lose all of your personal saves, info and accounts, complete a full backup first. Then, complete the rest of the pre requisites from below:
Read More..
This process will be easy to complete as Odin will be used for applying the root package on your SGS4. Actually you will flash a rooted JB 4.2.2 XXUBMGA OS on your device, which means that the operation will be similar with an update one. Do note that the root task in though unofficial, so the warranty of your S4 will get void. Anyway, this is not permanent, meaning that you can anytime choose to revoke the root access for reclaiming and regaining the warranty back. For revoking root access you will have to update your Galaxy S4 I9500 with an official release of the Android system, or you will have to downgrade to stock Jelly Bean 4.2.2 XXUBMGA software.
The advantages of root are numerous, but I do have to mention the following ones: on a rooted system you can access the OS and the internal system of the device for performing different operations such as removing in built programs or customize the performances; also on rooted handsets you can install a custom recovery image which can then be used for flashing custom ROMs and custom kernels; then, of course you will be able to overckock your Android device, or undervolt the same in case you need to upgrade the battery life; finally and as you may know, rooting is the first step to do when trying to speed up and upgrade the battery life of your smartphone / tablet.
Anyhow, before rooting your galaxy S4 just remember that the warranty will get void. So, be careful and try not to mess things up. Read the guidelines from below and everything will be fine.
Backup the text messages, call logs, internet settings, market apps and everything that’s important for you as the Galaxy S4 system might get wiped out or your data might get corrupted while applying the steps from below. If you want to avoid the unpleasant situation in which you lose all of your personal saves, info and accounts, complete a full backup first. Then, complete the rest of the pre requisites from below:
- Make sure that a Windows running computer can be used as you will have to download Odin and the root package suitable with your S4 on the same.
- On the computer there shouldn’t be installed antivirus, antimalware or any other security programs; if different before starting the root operation, deactivate the security protection.
- Since you will have to connect your phone with the computer, the USB cable should be near you; also due to same considerations, on your smartphone go to “Settings -> Applications -> Development” and enable the USB debugging option.
- Then, the process will take a while which means that your device might get turned off due to lack of battery. For avoiding that (your handset might get bricked if not) you should charge your SGS4 if there is less than 60% power left.
- Remember that this tutorial is compatible only with the Samsung Galaxy S4 I9500 that runs on stock / official Android 4.2.2 Jelly Bean XXUBMGA firmware. Trying to root a different device or a different Android software with the steps from below will most likely brick your Android based smartphone, or tablet.
How to Root Galaxy S4 I9500 on Official JB 4.2.2 XXUBMGA OS
- Download the root package by using the link from here.
- Unzip the package on desktop.
- Then, download and unzip Odin.
- Also, launch / run the program.
- Download Samsung KIES and install the S4 drivers if on your computer the drivers are not already installed.
- Turn off your phone as the fun begins.
- Wait a few seconds and then press on Power, volume down and home buttons – the download mode will be displayed.
- Connect your phone with the computer – use the USB cable.
- On Odin now you should notice the following: ID:COM section is either yellow or blue; the “added” message is there.
- If not, try to reinstall the drivers and then repeat the steps from above.
- For starting the root operation, first you will have to click on the “PDA” option.
- Then, you will have to select the root file.
- Finally, select “start”, but don’t make any other changes on Odin.
- Wait while your smartphone is being unlocked.
- In the end, Odin will display the “pass” message while the ID:COM section will be green.
- You can unplug the USB cable and reboot your device.
Tuesday, August 12, 2014
How to Easily Root Nexus 7 2013 Wi Fi on Android 4 4 1 and Install CWM KOT49E KitKat TWRP Recovery
Hi friends today I will try to give an Root of how the nexus 7, either the one we started from the introduction of Google has just released Android 4.4.1 OTA update with version Kitkat build KOT49E you to get the Wi-Fi version of the Nexus 7 (2013).
Note: You can manually download the OTA for Nexus 7 (2013) Wi-Fi directly from Google Server Update and follow the step-by-step guide to install the update manually.
Nexus 7 (2013) Wi-Fi users who have updated their devices with Android 4.4.1 KOT49E KitKat, can root their devices by using the tutorial below.
Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!
Pre-requisites
1. Make a backup of all your important data before following the guide.
2. Enable USB Debugging Mode on the tablet. Go to Settings >> About Phone. Tap on Build Number several times till the message shows "You are now a Developer". Exit from "About Phone" and find the "Developer Options" settings. Enable USB debugging.
3. The Nexus 7 bootloader should be unlocked.
4. Ensure the battery of the tablet is charged more than 80 percent.
5. The CWM/TWRP Recovery and SuperSU files compatible only with the Wi-Fi version of Nexus 7 (2013). Applying these on any incorrect variant will brick the device. Verify the model number of the Nexus 7 by navigating to Settings >> About Phone.
File Required
1. Android SDK
2. Fastboot
4. SuperSU (UPDATE-SuperSU-v1.75.zip) or the latest version
Steps to Root Nexus 7 (2013) Wi-Fi Running on Android 4.4.1 KOT49E KitKat and Install CWM/TWRP Recovery
- Install the Android SDK. The package includes the necessary drivers for connecting your tablet to the computer, which is mandatory for the rooting process.
- Extract the Fastboot .zip file using winrar/7zip/winzip or any other extracting tool and copy it to the android-sdk-windowsplatform-tools directory on the computer.
- Copy the CWM or TWRP .img file to the android-sdk-windowsplatform-tools directory on the computer.
- Connect the Nexus 7 to the computer using USB cable. Then copy the SuperSU .zip file to the SD card of your tablet.
- Switch off the Nexus 7. Then boot the device into fastboot mode by pressing and holding Volume Up, Volume Down, and Power buttons together.
- Navigate to android-sdk-windowsplatform-tools directory and open Command Prompt (Shift + Right-click >> Open Command Prompt). Then run the following command:
fastboot flash recovery recovery-clockwork-touch-6.0.4.3-grouper.img
- Once completed, choose RECOVERY from the Fastboot menu and enter Recovery Mode.
- In CWM Recovery, select "install zip from sdcard" and then select "choose zip from sdcard". Now, navigate to the SuperSU .zip file that you copied earlier and confirm the installation by selecting Yes.
- Once the installation process completes, return to main recovery menu and select "reboot system now".
Nexus 7 (2013) Wi-Fi running on Android 4.4.1 KOT49E KitKat is now rooted successfully. Open the app drawer of the Nexus 7 and look for an app called SuperSU. Verify the root status of the device by downloading Root Checker app from Google Play Store.
Subscribe to:
Posts (Atom)
